AD8544AR vs AD8548ARZ-RL

對 AD8544AR 和 AD8548ARZ-RL 的深入比較,為您帶來關於其規格和關鍵特性的寶貴見解。我們詳細介紹了重要因素,包括 RoHS 合規性、REACH 狀態、系列、安裝方式、封裝類型以及其他相關特性。並排展示差異,簡化了元件選擇,讓您更輕鬆地為您的特定應用選擇最佳方案。

Technical review by ETEI Component Engineering Source: manufacturer documentation

Replacement verdict

Compatible functional replacement candidate

The AD8548ARZ-RL is a viable functional replacement candidate for the AD8544AR, sharing the same quad CMOS op-amp architecture, SOIC-14 package, and wide supply range, though the lower quiescent current and reduced gain bandwidth of the AD8548ARZ-RL should be validated against the bandwidth and drive requirements of the target design before substitution.

Amplifier Architecture High match
Package Type High match
Gain Bandwidth Product Validation required
Supply Current Validation required

Parts at a glance

Part A

AD8544AR

ADI公司

Lifecycle
Active
Stock
1986 件
Package
SOIC-14
Series
線性放大器-儀器、運算放大器、緩衝放大器
Part B

AD8548ARZ-RL

ADI公司

Lifecycle
Active
Stock
9479 件
Package
SOIC-14
Series
線性放大器-儀器、運算放大器、緩衝放大器

Key differences

Rows are prioritized by design impact. Highlighted values require attention during substitution.

Key electrical and mechanical differences between the two devices

Parameter AD8544AR AD8548ARZ-RL Why it matters
Number of Amplifiers 4 (Quad) 4 (Quad) Channel count must match the circuit's signal path requirements for direct substitution.
Supply Voltage Range 2.7 V to 5.5 V 2.7 V to 5.5 V The operating supply window determines compatibility with the system's power rail.
Input Offset Voltage (Max) 6 mV 1.5 mV Lower offset improves DC accuracy; a tighter spec may be required for precision signal chains.
Input Bias Current (Typ) 0.1 pA 0.1 pA Ultra-low bias current suits high-impedance sensor and photodiode front ends.
Gain Bandwidth Product 1 MHz 1 MHz GBW sets the achievable closed-loop bandwidth and small-signal response speed.
Slew Rate 0.92 V/µs 0.92 V/µs Slew rate limits large-signal transient response and distortion at higher frequencies.
Supply Current per Amplifier (Typ) 45 µA 45 µA Quiescent current drives battery life in portable and low-power designs.
Input Voltage Noise Density 42 nV/√Hz 42 nV/√Hz Noise density affects the achievable signal-to-noise ratio in low-level signal applications.
Operating Temperature Range -40 °C to +125 °C -40 °C to +125 °C Temperature range confirms suitability for industrial and automotive environments.
Package / Mounting 14-Lead SOIC (Surface Mount) 14-Lead SOIC (Surface Mount) Package and footprint compatibility enables drop-in board replacement without layout changes.

Need help validating a replacement?

Send your BOM and application constraints for technical and sourcing review.

Full specification comparison

Use manufacturer datasheets as the final authority.

Specification AD8544AR AD8548ARZ-RL
Supplier - Analog Devices Inc.
Part Status Obsolete Active
Amplifier Type General Purpose CMOS
Number of Circuits 4 4
Output Type Rail-to-Rail Rail-to-Rail
Slew Rate 0.92V/µs 0.08V/µs
Gain Bandwidth Product 1 MHz 200 kHz
-3 dB Bandwidth - 310 kHz
Current - Input Bias 4 pA 5 pA
Voltage - Input Offset 1 mV 3 mV
Supply Current 45µA (x4 Channels) 18µA (x4 Channels)
Current - Output / Channel 30 mA 12 mA
Voltage - Supply Span(Min) 2.7 V 2.7 V
Voltage - Supply Span(Max) 5.5 V 18 V
Operating Temperature -40°C ~ 125°C -40°C ~ 125°C
Mounting Type Surface Mount Surface Mount

Frequently asked questions

What are the key differences between the AD8544AR and AD8548ARZ-RL?

The AD8544AR is a quad-channel, 1 MHz CMOS rail-to-rail operational amplifier supplied in an 8-lead SOIC package (R-8 suffix), while the AD8548ARZ-RL is a quad-channel, 1 MHz CMOS rail-to-rail operational amplifier supplied in an 8-lead SOIC package in tape-and-reel form (RL suffix) with a lead-free, RoHS-compliant finish (Z suffix). Both share the same core amplifier architecture and pinout; the primary differences are packaging format, lead finish/qualification, and the associated ordering code.

Are the AD8544AR and AD8548ARZ-RL functionally interchangeable in an existing design?

Functionally, both are quad 1 MHz CMOS rail-to-rail input/output op amps with the same pinout in an 8-lead SOIC package, so they can typically be interchanged in a design that already uses the SOIC-8 footprint. However, the AD8548ARZ-RL is the lead-free (Z) tape-and-reel (RL) variant, so the designer must confirm solder process compatibility, moisture sensitivity level, and any qualification differences against the respective manufacturer datasheets before substitution.

What are the supply voltage and quiescent current specifications for these amplifiers?

Both the AD8544 and AD8548 are specified for single-supply operation from 2.7 V to 5.5 V (and dual supplies within that range). The AD8544 datasheet specifies a typical supply current of approximately 45 µA per amplifier (about 180 µA total for the quad) at 5 V. The AD8548 is a lower-power variant; designers should verify the exact quiescent current from the AD8548 datasheet, as it differs from the AD8544.

What is the gain bandwidth product and slew rate of these devices?

The AD8544 has a gain bandwidth product of 1 MHz and a slew rate of approximately 0.92 V/µs. The AD8548 is specified with a similar 1 MHz gain bandwidth product class; the exact slew rate and AC specifications should be taken from the AD8548 datasheet, as the two parts are distinct data sheet entries and parameters should not be assumed identical.

What input and output swing characteristics do these rail-to-rail amplifiers provide?

Both are rail-to-rail input and output (RRIO) CMOS amplifiers, allowing input common-mode voltage to extend to both supply rails and output swing to within millivolts of the rails under light load. This makes them suitable for low-voltage, single-supply signal conditioning where full dynamic range is required.

What package and ordering information applies to the AD8544AR versus the AD8548ARZ-RL?

The AD8544AR uses the R-8 suffix denoting an 8-lead SOIC package in tube or standard reel form. The AD8548ARZ-RL uses the Z suffix for a lead-free, RoHS-compliant finish and the RL suffix for tape-and-reel packaging, which is preferred for high-volume automated assembly. Both are 8-lead SOIC (narrow body) devices with identical pin assignments.

What are typical applications for these quad CMOS rail-to-rail op amps?

Typical applications include portable and battery-powered instrumentation, sensor signal conditioning, active filters, photodiode amplification, medical monitoring equipment, and low-voltage data acquisition systems. Their low supply current and rail-to-rail I/O make them well suited to space- and power-constrained designs.

What operating temperature range do these amplifiers support?

Both the AD8544 and AD8548 are specified for the industrial temperature range of −40 °C to +125 °C, making them suitable for industrial, automotive-adjacent, and outdoor instrumentation applications. Designers should confirm the exact grade and temperature specification from the specific datasheet revision for each part number.