ADM4853ARZ
ADI公司
- Lifecycle
- Active
- Stock
- 6517 件
- Package
- SOIC-8
- Series
- 介面-驅動器、接收器、收發器
對 ADM4853ARZ 和 ADM4852AR 的深入比較,為您帶來關於其規格和關鍵特性的寶貴見解。我們詳細介紹了重要因素,包括 RoHS 合規性、REACH 狀態、系列、安裝方式、封裝類型以及其他相關特性。並排展示差異,簡化了元件選擇,讓您更輕鬆地為您的特定應用選擇最佳方案。
Replacement verdict
The ADM4853ARZ and ADM4852AR are both half-duplex RS-485/RS-422 transceivers from the same Analog Devices family, sharing an identical 8-lead SOIC footprint and the same 5 V supply and data-rate class. The ADM4853ARZ adds a driver enable pin and a receiver enable pin for independent direction control, whereas the ADM4852AR provides a single combined enable. For designs that do not require independent driver/receiver enable control, the ADM4852AR is a viable functional substitute; designs relying on separate enable pins should validate the control-pin behavior before substitution.
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADM4853ARZ | ADM4852AR | Why it matters |
|---|---|---|---|
| Data Rate | 20 Mbps | 2.5 Mbps | Maximum signaling speed; the higher-rate part can replace the lower-rate part in most designs, but not vice versa if full bandwidth is required. |
| Duplex Mode | Full duplex | Half duplex | Determines whether simultaneous transmit and receive is possible; full-duplex and half-duplex parts are not directly interchangeable on the same bus wiring. |
| Number of Drivers / Receivers | 1 driver / 1 receiver | 1 driver / 1 receiver | Defines the transceiver channel count; both are single-channel devices, so this does not differentiate them functionally. |
| Receiver Input Impedance (Unit Loads) | 1 unit load (12 kΩ) | 1 unit load (12 kΩ) | Determines how many nodes can share the bus; both being 1 unit load allows up to 32 standard nodes. |
| Supply Voltage | 5 V | 5 V | Operating supply rail; both require a 5 V supply, so power-supply compatibility is identical. |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C | Industrial temperature range; identical ratings mean both suit the same environmental conditions. |
| Package / Mounting | 8-Lead SOIC (surface mount) | 8-Lead SOIC (surface mount) | Footprint and assembly compatibility; identical packages allow drop-in board replacement. |
| Fail-Safe Receiver | Yes (open-circuit, short-circuit, idle-bus) | Yes (open-circuit, short-circuit, idle-bus) | Ensures a defined logic output when the bus is idle or faulted; both provide this, so behavior is equivalent. |
| ESD Protection (Bus Pins) | ±15 kV (HBM) | ±15 kV (HBM) | Robustness against electrostatic discharge on the bus; identical ratings mean equal field reliability. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADM4853ARZ | ADM4852AR |
|---|---|---|
| Supplier | - | Rochester Electronics, LLC |
| Part Status | Active | Obsolete |
| Type | Transceiver | Transceiver |
| Protocol | RS422, RS485 | RS422, RS485 |
| Number of Drivers/Receivers | 1/1 | 1/1 |
| Voltage - Supply | 4.75V ~ 5.25V | 4.75V ~ 5.25V |
| Mounting Type | Surface Mount | Surface Mount |
| Duplex | Half | - |
| Receiver Hysteresis | 20 mV | - |
| Data Rate | 10Mbps | - |
| Operating Temperature | -40°C ~ 85°C | - |
The ADM4853ARZ and ADM4852AR are both half-duplex RS-485/RS-422 transceivers from Analog Devices in an 8-lead SOIC package, but they differ in data rate and slew-rate behavior. The ADM4853ARZ is specified for data rates up to 10 Mbps, while the ADM4852AR is a limited-slew-rate device specified for data rates up to 2.5 Mbps. The lower slew rate of the ADM4852AR reduces EMI and improves signal integrity on long cables, whereas the ADM4853ARZ supports higher-speed communication.
Yes. Both devices are offered in the same 8-lead SOIC (R-8) package with the same pinout: RO, RE, DE, DI, GND, A, B, and VCC. This allows the ADM4852AR and ADM4853ARZ to share the same PCB land pattern, though the data-rate and slew-rate differences must be validated for the target application.
Not unconditionally. Because the ADM4852AR is limited to 2.5 Mbps while the ADM4853ARZ supports up to 10 Mbps, the ADM4852AR cannot replace the ADM4853ARZ in designs that require data rates above 2.5 Mbps. In applications operating at or below 2.5 Mbps, the ADM4852AR may be considered, but the designer must verify that the reduced slew rate and any associated timing differences meet the system requirements.
The ADM4853ARZ supports data rates up to 10 Mbps. The ADM4852AR supports data rates up to 2.5 Mbps due to its limited slew-rate output driver, which is intended to reduce electromagnetic interference and reflections on long transmission lines.
Yes. Both the ADM4853ARZ and ADM4852AR are specified for operation from a single 5 V ±5% supply (4.75 V to 5.25 V), consistent with the standard ADM485x family of RS-485/RS-422 transceivers from Analog Devices.
Yes. Both are half-duplex transceivers with separate receiver enable (RE) and driver enable (DE) pins, and they feature a differential driver and receiver compliant with RS-485 and RS-422 signaling. They are intended for multipoint bus transmission on half-duplex networks.
The ADM4852AR is generally preferred for long-cable or EMI-sensitive environments because its limited slew rate reduces high-frequency emissions and signal reflections. The ADM4853ARZ, with its higher 10 Mbps capability, is better suited to shorter links or applications requiring higher throughput where the faster edges can be tolerated.