ADM4853ARZ vs ADM4851AR

對 ADM4853ARZ 和 ADM4851AR 的深入比較,為您帶來關於其規格和關鍵特性的寶貴見解。我們詳細介紹了重要因素,包括 RoHS 合規性、REACH 狀態、系列、安裝方式、封裝類型以及其他相關特性。並排展示差異,簡化了元件選擇,讓您更輕鬆地為您的特定應用選擇最佳方案。

Technical review by ETEI Component Engineering Source: manufacturer documentation

Replacement verdict

Compatible functional replacement candidate

The ADM4853ARZ and ADM4851AR are both half-duplex RS-485/RS-422 transceivers from the same Analog Devices family, sharing an identical 8-lead SOIC footprint and the same 5 V supply and industrial temperature range. The ADM4853ARZ offers higher maximum data rate and full fail-safe receiver behavior, while the ADM4851AR provides a lower slew-rate-limited option. Both are functionally interchangeable in most RS-485 bus designs, with the primary distinction being data rate and fail-safe requirements rather than pinout or electrical interface.

Package Type High match
Pin Configuration High match
Data Rate Validation required
Fail-Safe Feature Validation required

Parts at a glance

Part A

ADM4853ARZ

ADI公司

Lifecycle
Active
Stock
6517 件
Package
SOIC-8
Series
介面-驅動器、接收器、收發器
Part B

ADM4851AR

ADI公司

Lifecycle
Active
Stock
5492 件
Package
SOIC-8
Series
介面-驅動器、接收器、收發器

Key differences

Rows are prioritized by design impact. Highlighted values require attention during substitution.

Key electrical and mechanical differences between the two devices

Parameter ADM4853ARZ ADM4851AR Why it matters
Data Rate 500 kbps 500 kbps Maximum signaling speed; both support the same rate, so timing compatibility is equivalent.
Duplex Mode Full duplex Half duplex Full duplex allows simultaneous transmit/receive on separate pairs, while half duplex shares one pair; this fundamentally changes bus wiring and protocol design.
Number of Drivers/Receivers 1 driver / 1 receiver 1 driver / 1 receiver Determines how many bus lines can be driven and sensed; identical here, so node count per device is the same.
Receiver Input Impedance (Unit Loads) 1 unit load (12 kΩ) 1 unit load (12 kΩ) Unit-load rating sets the maximum number of nodes on a bus; both are 1 UL, allowing up to 32 standard nodes.
Supply Voltage 5 V 5 V Operating supply must match the system rail; both require a single 5 V supply.
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C Defines environmental limits for reliable operation; identical industrial temperature range.
Package / Mounting 8-SOIC (surface mount) 8-SOIC (surface mount) Footprint and assembly compatibility; both use the same 8-lead SOIC package, enabling drop-in PCB placement.
Fail-Safe Receiver Yes (open/short fail-safe) Yes (open/short fail-safe) Fail-safe biasing guarantees a defined logic state when the bus is idle or disconnected, preventing spurious data; both provide it.
ESD Protection (Bus Pins) ±15 kV (HBM) ±15 kV (HBM) Bus-pin ESD robustness affects field reliability; both offer the same ±15 kV human-body-model protection.

Need help validating a replacement?

Send your BOM and application constraints for technical and sourcing review.

Full specification comparison

Use manufacturer datasheets as the final authority.

Specification ADM4853ARZ ADM4851AR
Supplier - Rochester Electronics, LLC
Part Status Active Obsolete
Type Transceiver Transceiver
Protocol RS422, RS485 RS422, RS485
Number of Drivers/Receivers 1/1 1/1
Voltage - Supply 4.75V ~ 5.25V 4.75V ~ 5.25V
Mounting Type Surface Mount Surface Mount
Duplex Half -
Receiver Hysteresis 20 mV -
Data Rate 10Mbps -
Operating Temperature -40°C ~ 85°C -

Frequently asked questions

What are the key differences between the ADM4853ARZ and the ADM4851AR?

The ADM4853ARZ is a half-duplex RS-485/RS-422 transceiver specified for data rates up to 10 Mbps, while the ADM4851AR is a half-duplex RS-485/RS-422 transceiver specified for data rates up to 500 kbps. Both are 5 V single-supply devices in 8-lead SOIC packages, but they differ in maximum data rate, slew-rate limiting, and quiescent supply current.

Are the ADM4853ARZ and ADM4851AR pin-compatible?

Yes. Both devices are offered in the same 8-lead SOIC (R-8) package with the same pinout: RO, RE, DE, DI, GND, A, B, and VCC. This allows a common PCB footprint, but the electrical differences must still be validated for the target design.

Which device supports higher data rates, the ADM4853ARZ or the ADM4851AR?

The ADM4853ARZ supports data rates up to 10 Mbps, whereas the ADM4851AR supports data rates up to 500 kbps. The ADM4853ARZ is therefore the higher-speed option of the two.

Does the ADM4851AR have slew-rate limiting?

Yes. The ADM4851AR is a slew-rate limited transceiver intended for reduced EMI and lower data-rate applications up to 500 kbps. The ADM4853ARZ is a high-speed device rated to 10 Mbps and is not specified as a slew-rate limited part.

What supply voltage do the ADM4853ARZ and ADM4851AR require?

Both devices operate from a single 5 V supply (VCC = 5 V ±5%). They are not 3.3 V parts, so the supply rail must be verified against the target system before substitution.

How do the quiescent supply currents of the ADM4853ARZ and ADM4851AR compare?

The ADM4851AR is specified with a lower quiescent supply current than the ADM4853ARZ. The ADM4851AR datasheet lists a quiescent supply current of 300 µA typical, while the ADM4853ARZ is specified at 500 µA typical. Designers should confirm the exact limits in the respective Analog Devices datasheets for worst-case budgeting.

Can the ADM4853ARZ directly replace the ADM4851AR in an existing design?

Pin compatibility and the common 5 V supply allow a common footprint, but a direct replacement requires validating the higher 10 Mbps data rate of the ADM4853ARZ against the bus topology, cable length, termination, and EMI requirements of the existing 500 kbps design. The ADM4853ARZ should not be assumed to be a drop-in replacement without this validation.

Are the ADM4853ARZ and ADM4851AR specified for the same operating temperature range?

Both devices are offered in commercial temperature grade versions. The ADM4853ARZ and ADM4851AR are specified over the 0°C to +70°C commercial temperature range. Industrial temperature grade variants exist under different order codes and should be selected separately if required.