ADM4853ARZ vs ADM4850AR

對 ADM4853ARZ 和 ADM4850AR 的深入比較,為您帶來關於其規格和關鍵特性的寶貴見解。我們詳細介紹了重要因素,包括 RoHS 合規性、REACH 狀態、系列、安裝方式、封裝類型以及其他相關特性。並排展示差異,簡化了元件選擇,讓您更輕鬆地為您的特定應用選擇最佳方案。

Technical review by ETEI Component Engineering Source: manufacturer documentation

Replacement verdict

Compatible functional replacement candidate

The ADM4853ARZ and ADM4850AR are both half-duplex RS-485/RS-422 transceivers in an 8-lead SOIC package with matched supply voltage and data-rate class, making the ADM4853ARZ a viable functional replacement candidate for the ADM4850AR. Designers should validate the receiver input impedance and fail-safe behavior against the target bus before committing to production.

Interface Protocol High match
Package Type High match
Supply Voltage High match
Receiver Input Impedance Validation required

Parts at a glance

Part A

ADM4853ARZ

ADI公司

Lifecycle
Active
Stock
6517 件
Package
SOIC-8
Series
介面-驅動器、接收器、收發器
Part B

ADM4850AR

ADI公司

Lifecycle
Active
Stock
9264 件
Package
SOIC-8
Series
介面-驅動器、接收器、收發器

Key differences

Rows are prioritized by design impact. Highlighted values require attention during substitution.

Key electrical and mechanical differences between the two devices

Parameter ADM4853ARZ ADM4850AR Why it matters
Data Rate 10 Mbps 250 kbps Maximum signaling speed; the faster part supports higher-throughput buses while the slower part is limited to low-speed networks.
Duplex Mode Full duplex Half duplex Full duplex allows simultaneous transmit and receive on separate pairs, while half duplex shares one pair and cannot be substituted without reworking the bus topology.
Number of Drivers/Receivers 1 driver / 1 receiver 1 driver / 1 receiver Confirms both are single-channel transceivers, so the node count per bus is comparable.
Supply Voltage 5 V 5 V Both operate from a 5 V rail, so power-supply design is compatible between the two parts.
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C Identical industrial temperature ratings mean both suit the same environmental conditions.
Package / Mounting 8-SOIC, surface mount 8-SOIC, surface mount Same package and footprint allow drop-in board replacement without layout changes.
Receiver Input Impedance (Unit Loads) 1 unit load 1 unit load Both present one unit load, permitting up to 32 nodes on a standard RS-485 bus.
Fail-Safe Receiver Yes (open-circuit fail-safe) Yes (open-circuit fail-safe) Both define a known output state on open inputs, preventing indeterminate logic levels during idle bus conditions.

Need help validating a replacement?

Send your BOM and application constraints for technical and sourcing review.

Full specification comparison

Use manufacturer datasheets as the final authority.

Specification ADM4853ARZ ADM4850AR
Supplier - Rochester Electronics, LLC
Part Status Active Obsolete
Type Transceiver Transceiver
Protocol RS422, RS485 RS422, RS485
Number of Drivers/Receivers 1/1 1/1
Voltage - Supply 4.75V ~ 5.25V 4.75V ~ 5.25V
Mounting Type Surface Mount Surface Mount
Duplex Half -
Receiver Hysteresis 20 mV -
Data Rate 10Mbps -
Operating Temperature -40°C ~ 85°C -

Frequently asked questions

What are the key differences between the ADM4853ARZ and the ADM4850AR?

The ADM4853ARZ is a half-duplex RS-485/RS-422 transceiver specified for data rates up to 10 Mbps, while the ADM4850AR is a half-duplex RS-485/RS-422 transceiver specified for data rates up to 2.5 Mbps. Both are 5 V single-supply devices in 8-lead SOIC packages, but they differ in maximum data rate, slew-rate limiting, and operating temperature range.

Are the ADM4853ARZ and ADM4850AR pin-compatible?

Yes. Both devices are offered in an 8-lead SOIC package with the same pinout (RO, RE, DE, DI, GND, A, B, VCC), so they are pin-compatible and share the same PCB land pattern.

What is the maximum data rate of each device?

The ADM4853ARZ supports data rates up to 10 Mbps. The ADM4850AR supports data rates up to 2.5 Mbps.

Do these transceivers have slew-rate-limited outputs?

Yes. The ADM4850AR is a slew-rate-limited version intended to reduce EMI and reflections, which limits it to 2.5 Mbps. The ADM4853ARZ is a full-speed (non-slew-rate-limited) version rated for 10 Mbps.

What supply voltage and temperature range do these parts support?

Both devices operate from a single 5 V supply. The ADM4853ARZ is specified over the industrial temperature range of −40°C to +85°C. The ADM4850AR is specified over the commercial temperature range of 0°C to +70°C.

Can the ADM4850AR be used as a drop-in replacement for the ADM4853ARZ?

Only if the system's data rate does not exceed 2.5 Mbps and the operating temperature stays within 0°C to +70°C. Because the ADM4850AR is slew-rate limited and rated for a narrower temperature range, it cannot replace the ADM4853ARZ in applications requiring 10 Mbps or operation below 0°C.

Are both devices compliant with the RS-485 and RS-422 standards?

Yes. Both the ADM4853ARZ and ADM4850AR are RS-485/RS-422 transceivers designed to meet the electrical requirements of the TIA/EIA-485 and TIA/EIA-422 standards for balanced differential data transmission.