AD8429ARZ
ADI公司
- Lifecycle
- Active
- Stock
- 7143 件
- Package
- SOIC-8
- Series
- 線性放大器-儀器、運算放大器、緩衝放大器
對 AD8429ARZ 和 AD8421ARZ-RL 的深入比較,為您帶來關於其規格和關鍵特性的寶貴見解。我們詳細介紹了重要因素,包括 RoHS 合規性、REACH 狀態、系列、安裝方式、封裝類型以及其他相關特性。並排展示差異,簡化了元件選擇,讓您更輕鬆地為您的特定應用選擇最佳方案。
Replacement verdict
The AD8429ARZ and AD8421ARZ-RL are both precision instrumentation amplifiers in the same SOIC-8 package with identical pinout, making them strong functional replacement candidates. However, they differ in gain range, bandwidth, and noise performance, so the AD8421ARZ-RL should be validated against the specific gain, frequency, and noise requirements of the target design before substitution.
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | AD8429ARZ | AD8421ARZ-RL | Why it matters |
|---|---|---|---|
| Input Voltage Noise (1 kHz, typ) | 1 nV/√Hz | 3 nV/√Hz | Lower input voltage noise improves signal-to-noise ratio for low-level sensor signals, making the AD8429 preferable for very low-noise applications. |
| Gain Bandwidth Product (G = 1, typ) | 15 MHz | 10 MHz | Higher bandwidth supports wider signal frequency ranges and faster settling, affecting dynamic performance in instrumentation front ends. |
| Input Offset Voltage (max, RTI) | 50 µV | 60 µV | Lower offset voltage reduces DC error at the output, important for precision measurement and high-gain amplification. |
| Input Bias Current (max) | 100 nA | 500 pA | Much lower bias current in the AD8421 minimizes errors with high source impedances, making it better suited for high-impedance sensors. |
| CMRR (G = 100, min) | 120 dB | 114 dB | Higher common-mode rejection suppresses interference and ground noise, critical for extracting small differential signals in noisy environments. |
| Supply Current (max) | 4.5 mA | 2.3 mA | Lower supply current in the AD8421 reduces power consumption, beneficial for portable and power-constrained designs. |
| Supply Voltage Range | ±4 V to ±18 V | ±2.5 V to ±18 V | The wider low-end supply range of the AD8421 allows operation at lower supply voltages, enabling use in low-voltage systems. |
| Operating Temperature Range | −40°C to +125°C | −40°C to +85°C | The extended upper temperature range of the AD8429 supports harsher environments and higher-temperature applications. |
| Package | 8-Lead SOIC | 8-Lead SOIC | Identical package and pinout allow direct board-level substitution without layout changes. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | AD8429ARZ | AD8421ARZ-RL |
|---|---|---|
| Supplier | - | Analog Devices Inc. |
| Part Status | Active | Active |
| Amplifier Type | Instrumentation | Instrumentation |
| Number of Circuits | 1 | 1 |
| Slew Rate | 22V/µs | 35V/µs |
| -3 dB Bandwidth | 15 MHz | 10 MHz |
| Current - Input Bias | 300 nA | 1 nA |
| Voltage - Input Offset | 150 µV | 60 µV |
| Supply Current | 6.7mA | 2mA |
| Current - Output / Channel | 35 mA | 65 mA |
| Voltage - Supply Span(Min) | 8 V | 5 V |
| Voltage - Supply Span(Max) | 36 V | 36 V |
| Operating Temperature | -40°C ~ 125°C | -40°C ~ 85°C |
| Mounting Type | Surface Mount | Surface Mount |
The AD8429ARZ is a low-noise instrumentation amplifier optimized for ultra-low noise (1 nV/√Hz) with a gain range of 1 to 10,000, while the AD8421ARZ-RL is a lower-power, lower-cost instrumentation amplifier with 3 nV/√Hz noise and a gain range of 1 to 10,000. The AD8421ARZ-RL is supplied in tape-and-reel packaging (RL suffix), whereas the AD8429ARZ is typically supplied in tubes. Both are available in 8-lead SOIC packages.
Yes, both devices are offered in an 8-lead SOIC package with the same pinout (gain resistor pins, +IN, -IN, +VS, -VS, REF, and OUT), allowing them to share the same PCB land pattern. However, designers should verify the specific package variant and thermal considerations against the respective datasheets before substitution.
The AD8429ARZ has an input voltage noise density of approximately 1 nV/√Hz at 1 kHz, making it suitable for ultra-low-noise applications. The AD8421ARZ-RL has an input voltage noise density of approximately 3 nV/√Hz at 1 kHz. The AD8429ARZ therefore offers lower noise, while the AD8421ARZ-RL provides a balance of lower power consumption and cost.
Both devices operate from dual supplies typically ranging from ±2.25 V to ±18 V (or single-supply equivalents). The AD8429ARZ draws a typical quiescent current of about 4.5 mA, while the AD8421ARZ-RL draws a lower typical quiescent current of about 2.3 mA, making the AD8421ARZ-RL preferable for power-sensitive designs.
The "RL" suffix indicates tape-and-reel packaging, which is intended for automated pick-and-place assembly in high-volume production. The AD8429ARZ without an RL suffix is typically supplied in tube packaging. Both are the same die and performance grade; only the packaging format differs.
Because the AD8421ARZ-RL has higher input voltage noise (approximately 3 nV/√Hz versus 1 nV/√Hz), it is not a direct drop-in replacement in designs where the ultra-low noise floor of the AD8429ARZ is critical. In applications where 3 nV/√Hz noise is acceptable and lower power is desired, the AD8421ARZ-RL may be considered after validating gain, bandwidth, and CMRR requirements against the datasheets.
Both devices use a single external resistor between the RG pins to set gain, with the gain equation G = 1 + (6 kΩ / RG) for the AD8429ARZ and G = 1 + (9.9 kΩ / RG) for the AD8421ARZ-RL. Designers must recalculate the gain resistor value when substituting between the two parts.
The AD8429ARZ offers a -3 dB bandwidth of approximately 1.2 MHz at G = 1 and CMRR of about 90 dB at G = 1 (DC to 60 Hz). The AD8421ARZ-RL offers a -3 dB bandwidth of approximately 10 MHz at G = 1 and CMRR of about 80 dB at G = 1. The AD8421ARZ-RL provides wider bandwidth, while the AD8429ARZ provides higher CMRR at low gain.