Part A
ADSP-BF548BBCZ-5A
ADI公司
- Lifecycle
- Active
- Stock
- 6104 件
- Package
- LFBGA-400
- Series
- 嵌入式-DSP（數位信號處理器）
Replacement verdict
Not a drop-in replacement
The ADSP-BF548BBCZ-5A and ADSP-BF536BBC-4A are not drop-in replacements for one another. Although both are Blackfin fixed-point DSPs sharing the same core architecture family, they differ in package footprint, on-chip memory density, integrated peripheral set, and clock speed, so a direct board-level substitution is not feasible without redesign.
Different package footprint
Different on-chip memory
Different peripheral set
Different core clock speed
Parts at a glance
Part B
ADSP-BF536BBC-4A
ADI公司
- Lifecycle
- Active
- Stock
- 4718 件
- Package
- LFBGA-182
- Series
- 嵌入式-DSP（數位信號處理器）
Key differences
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADSP-BF548BBCZ-5A | ADSP-BF536BBC-4A | Why it matters |
|---|---|---|---|
| Core Clock Frequency (max) | 533 MHz | 400 MHz | Determines maximum processing throughput; a faster core enables more DSP/MCU work per unit time and affects real-time performance. |
| On-chip SRAM | 132 kB (L1 + L2) | 52 kB (L1 + L2) | Larger internal memory reduces external memory accesses and latency, which is critical for deterministic signal processing. |
| Package / Pin Count | BGA-289 (17x17 mm) | BGA-208 (17x17 mm) | Different package and pin count affect PCB footprint, routing, and whether the parts are drop-in compatible on an existing board. |
| External Memory Interface | DDR/SDRAM, async SRAM, NAND/NOR flash | SDRAM, async SRAM, NAND/NOR flash | Support for DDR memory on the BF548 enables higher bandwidth and larger memory configurations than the SDRAM-only BF536. |
| Ethernet MAC | 10/100 Ethernet MAC | 10/100 Ethernet MAC | Both integrate an Ethernet MAC, but the surrounding peripherals and memory bandwidth differ, affecting networked application capability. |
| USB Support | USB 2.0 HS OTG (with PHY) | USB 2.0 FS device (no HS PHY) | High-speed USB OTG on the BF548 supports faster data transfer and host/device roles, while the BF536 is limited to full-speed device operation. |
| Supply Voltage (core) | 1.10 V - 1.35 V | 0.95 V - 1.15 V | Core voltage ranges differ, so power supply design and level compatibility must be re-validated when substituting parts. |
| Operating Temperature Range | -40 °C to +85 °C (industrial) | -40 °C to +85 °C (industrial) | Both are rated for industrial temperature, so environmental robustness is comparable for harsh deployments. |
| PPI / Parallel Peripheral Interface | Yes (with dedicated DMA) | Yes (with dedicated DMA) | The PPI enables direct connection to LCDs, cameras, and ADCs; both support it, but bandwidth scales with core and memory speed. |
Need help validating a replacement?
Send your BOM and application constraints for technical and sourcing review.
Full specification comparison
Use manufacturer datasheets as the final authority.
| Specification | ADSP-BF548BBCZ-5A | ADSP-BF536BBC-4A |
|---|---|---|
| Supplier | - | Rochester Electronics, LLC |
| Series | Blackfin® | Blackfin® |
| Part Status | Active | Obsolete |
| Type | Fixed Point | Fixed Point |
| Interface | CAN, SPI, SSP, TWI, UART, USB | CAN, SPI, SSP, TWI, UART |
| Clock Rate | 533MHz | 400MHz |
| Non - Volatile Memory | External | External |
| On - Chip RAM | 260kB | 100kB |
| Voltage - I / O | 2.50V, 3.30V | 2.50V, 3.30V |
| Voltage - Core | 1.25V | 1.20V |
| Operating Temperature | -40°C ~ 85°C (TA) | -40°C ~ 85°C |
| Mounting Type | Surface Mount | Surface Mount |
Frequently asked questions
What are the key architectural differences between the ADSP-BF548BBCZ-5A and the ADSP-BF536BBC-4A?
The ADSP-BF548BBCZ-5A is a Blackfin processor with a 533 MHz core clock, 260 KB of on-chip SRAM, and integrated peripherals including a 32-bit DDR SDRAM controller, USB 2.0 HS OTG, and an ATAPI controller. The ADSP-BF536BBC-4A operates at 400 MHz with 132 KB of on-chip SRAM and a more limited peripheral set, lacking the DDR controller and USB HS OTG block found on the BF548.
Are the ADSP-BF548BBCZ-5A and ADSP-BF536BBC-4A pin-compatible?
No. The ADSP-BF548BBCZ-5A is supplied in a 289-ball BGA package, while the ADSP-BF536BBC-4A is supplied in a 208-ball BGA package. The different ball counts and land patterns mean they are not drop-in replacements and require different PCB footprints.
Can the ADSP-BF536BBC-4A be used as a direct substitute for the ADSP-BF548BBCZ-5A in an existing design?
No. Beyond the package and pinout differences, the two parts differ in core clock (400 MHz vs 533 MHz), on-chip memory size, and integrated peripherals such as the DDR SDRAM controller and USB HS OTG present on the BF548 but not the BF536. A direct substitution would require schematic, layout, and firmware changes validated against the respective datasheets.
What are the operating temperature ranges for these two processors?
Both the ADSP-BF548BBCZ-5A and the ADSP-BF536BBC-4A are specified for the industrial temperature range of −40 °C to +85 °C, as indicated by the "B" temperature code in their part numbers and confirmed in the Analog Devices Blackfin datasheets.
How do the on-chip memory resources of the two parts compare?
The ADSP-BF548BBCZ-5A provides 260 KB of on-chip SRAM (including 64 KB of L1 instruction memory, 64 KB of L1 data memory, and 128 KB of L2 SRAM plus 4 KB of scratchpad). The ADSP-BF536BBC-4A provides 132 KB of on-chip SRAM (64 KB L1 instruction, 64 KB L1 data, and 4 KB scratchpad), with no L2 SRAM block.
Which external memory interfaces are supported by each device?
The ADSP-BF548BBCZ-5A includes a 32-bit DDR SDRAM controller and a separate asynchronous memory controller supporting SRAM, ROM, and flash. The ADSP-BF536BBC-4A provides only an asynchronous external memory interface for SRAM, ROM, and flash, and does not include a DDR SDRAM controller.
Do both parts support USB connectivity?
The ADSP-BF548BBCZ-5A integrates a USB 2.0 high-speed On-The-Go (OTG) controller. The ADSP-BF536BBC-4A does not include a USB controller and would require an external USB device or host controller if USB connectivity is needed.
What are the core supply voltages for the ADSP-BF548BBCZ-5A and ADSP-BF536BBC-4A?
Both devices use a 1.2 V core supply (VDDINT) and a 2.5 V or 3.3 V I/O supply (VDDEXT), consistent with the Analog Devices Blackfin datasheet specifications for these speed-grade and temperature-grade variants.