ADS1281IPW
德州儀器
- Lifecycle
- Active
- Stock
- 4383 件
- Package
- TSSOP-24
- Series
- 資料獲取-模數轉換器(ADC)
對 ADS1281IPW 和 ADS1271IPWG4 的深入比較,為您帶來關於其規格和關鍵特性的寶貴見解。我們詳細介紹了重要因素,包括 RoHS 合規性、REACH 狀態、系列、安裝方式、封裝類型以及其他相關特性。並排展示差異,簡化了元件選擇,讓您更輕鬆地為您的特定應用選擇最佳方案。
Replacement verdict
The ADS1281IPW and ADS1271IPWG4 are both 24-bit delta-sigma ADCs in a TSSOP-24 package, but they differ in resolution architecture, data rate, and interface configuration. The ADS1281IPW offers higher resolution and lower noise for seismic and precision applications, while the ADS1271IPWG4 provides a wider selectable data rate range and flexible SPI-compatible interface. Designers should validate clock requirements, digital interface timing, and reference configuration before substituting one for the other in an existing design.
德州儀器
德州儀器
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADS1281IPW | ADS1271IPWG4 | Why it matters |
|---|---|---|---|
| Resolution (bits) | 31 | 24 | Higher resolution provides finer measurement granularity and lower quantization noise, which is critical for precision sensor and seismic applications. |
| Maximum Sample Rate (SPS) | 4000 | 105000 | Sample rate determines the maximum signal bandwidth the ADC can capture; the ADS1271 supports much faster data acquisition. |
| Architecture | Delta-Sigma | Delta-Sigma | Both use delta-sigma conversion, but the ADS1281 is optimized for ultra-high resolution while the ADS1271 targets wider bandwidth. |
| Input Type | Differential | Differential | Differential inputs improve common-mode noise rejection, important for low-level signal measurement in noisy environments. |
| Supply Voltage (Analog) | 5 V | 5 V | Analog supply voltage must match the system rail; both operate from a 5 V analog supply, easing board-level substitution. |
| Interface | SPI | SPI | A compatible serial interface simplifies firmware and host processor integration when swapping parts. |
| Package | TSSOP-24 | TSSOP-24 | Matching package and pin count allows drop-in PCB compatibility without layout changes. |
| Operating Temperature Range | -40 to +85 °C | -40 to +105 °C | Wider temperature range affects suitability for industrial and harsh-environment deployments. |
| Power Consumption (typical) | 12 mW | 70 mW | Lower power dissipation reduces thermal load and extends battery life in portable or energy-sensitive systems. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADS1281IPW | ADS1271IPWG4 |
|---|---|---|
| Supplier | - | Texas Instruments |
| Part Status | Active | Discontinued at Digi-Key |
| Number of Bits | 31 | 24 |
| Sampling Rate(Per Second) | 4k | 105k |
| Number of Inputs | 1 | 1 |
| Input Type | Differential, Single Ended | Differential |
| Data Interface | SPI | SPI |
| Configuration | ADC | ADC |
| Number of A/D Converters | 1 | 1 |
| Architecture | Sigma-Delta | Sigma-Delta |
| Reference Type | External | External |
| Voltage - Supply, Analog | 5V | 5V |
| Voltage - Supply, Digital | 1.65V ~ 3.6V | 1.65V ~ 3.6V |
| Operating Temperature | -40°C ~ 85°C | -40°C ~ 105°C |
The ADS1281IPW is a single-channel, 31-bit delta-sigma ADC designed for high-resolution seismic and energy exploration applications, featuring a programmable gain amplifier and selectable digital filter options. The ADS1271IPWG4 is a 24-bit, single-channel delta-sigma ADC optimized for wide-bandwidth industrial measurement with a fixed 105 kSPS data rate and a choice of three filter modes (high-speed, high-resolution, low-power). The ADS1281 offers higher resolution (31-bit) and lower noise for low-frequency signals, while the ADS1271 provides wider signal bandwidth and faster throughput.
No. Both devices are offered in a 24-pin TSSOP package (PW suffix), but their pin functions and internal architectures differ. The ADS1281IPW includes dedicated pins for a programmable gain amplifier input, reference buffers, and synchronization, while the ADS1271IPWG4 has a different pin assignment for its clock, filter mode selection, and data-ready signaling. A direct PCB drop-in replacement is not supported without layout and schematic changes.
The ADS1281IPW supports programmable output data rates from 250 SPS to 4 kSPS, depending on the selected digital filter and clock configuration, making it suitable for low-frequency, high-resolution measurements. The ADS1271IPWG4 provides a fixed 105 kSPS output data rate in high-speed mode, with lower rates available in high-resolution and low-power modes. The ADS1271 is therefore better suited for applications requiring wider bandwidth, while the ADS1281 targets precision low-frequency signal acquisition.
The ADS1281IPW is specified with very low input-referred noise and high resolution (31-bit) tailored for seismic and low-frequency precision measurement, typically achieving noise levels in the sub-microvolt range at low data rates. The ADS1271IPWG4, while a high-performance 24-bit converter, is optimized for wider bandwidth industrial applications and does not match the ADS1281's low-frequency noise floor. For low-frequency, high-resolution acquisition, the ADS1281IPW is the more appropriate choice.
The ADS1281IPW operates from an analog supply of 5 V (with a separate digital supply of 1.8 V to 3.3 V) and typically consumes approximately 12 mW in normal operation. The ADS1271IPWG4 operates from a 5 V analog supply and a 1.8 V to 3.3 V digital supply, with power consumption typically around 130 mW in high-speed mode and lower in low-power mode. The ADS1281 is significantly lower power, reflecting its low-frequency precision design target.
No, not directly. The ADS1281IPW is specifically designed for seismic and energy exploration with 31-bit resolution, programmable gain, and low-frequency digital filter options optimized for geophone and hydrophone signals. The ADS1271IPWG4 offers 24-bit resolution and a fixed 105 kSPS rate with different filter characteristics, which may not meet the dynamic range and noise requirements of seismic acquisition. Replacement would require thorough validation against the application's resolution, noise, and filter requirements.
The ADS1281IPW provides selectable digital filter options including a linear-phase finite impulse response (FIR) filter, a low-latency sinc filter, and a high-resolution filter, configurable via register settings to suit different low-frequency measurement needs. The ADS1271IPWG4 offers three fixed filter modes: high-speed, high-resolution, and low-power, selected via dedicated pins. The ADS1281's filter programmability provides greater flexibility for precision low-frequency applications, while the ADS1271's pin-selectable modes simplify configuration for industrial designs.
The ADS1271IPWG4 is more suitable for wide-bandwidth industrial measurement. Its 105 kSPS data rate and high-speed filter mode support signal bandwidths up to approximately 50 kHz, making it appropriate for vibration, power monitoring, and industrial control applications. The ADS1281IPW, with a maximum 4 kSPS data rate, is intended for low-frequency precision measurements and does not provide the bandwidth required for wide-band industrial signal acquisition.