ADM3050EBRIZ
ADI公司
- Lifecycle
- Active
- Stock
- 5255 件
- Package
- SOIC-8
- Series
- 介面-驅動器、接收器、收發器
對 ADM3050EBRIZ 和 ADM3076EARZ 的深入比較,為您帶來關於其規格和關鍵特性的寶貴見解。我們詳細介紹了重要因素,包括 RoHS 合規性、REACH 狀態、系列、安裝方式、封裝類型以及其他相關特性。並排展示差異,簡化了元件選擇,讓您更輕鬆地為您的特定應用選擇最佳方案。
Replacement verdict
The ADM3076EARZ and ADM3050EBRIZ are not drop-in replacements for one another. Although both are Analog Devices isolated RS-485 transceivers, they differ in isolation technology, data rate, package footprint, and channel configuration, so a direct board-level substitution is not possible without design changes and revalidation.
ADI公司
ADI公司
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADM3076EARZ | ADM3050EBRIZ | Why it matters |
|---|---|---|---|
| Protocol / Interface Type | RS-485 / RS-422 (half-duplex transceiver) | CAN FD transceiver (ISO 11898) | These devices serve entirely different serial bus protocols, so they are not functionally interchangeable in a given network. |
| Data Rate | Up to 16 Mbps | Up to 12 Mbps (CAN FD) | Maximum supported bus speed determines whether the part meets the timing requirements of the target network. |
| Number of Drivers / Receivers | 1 driver / 1 receiver | 1 driver / 1 receiver | Both are single-channel transceivers, but the channel count alone does not make them substitutable across protocols. |
| Supply Voltage | 3.0 V to 3.6 V (3.3 V nominal) | 4.5 V to 5.5 V (5 V nominal) | Different supply rails mean the parts cannot drop into the same power domain without redesign. |
| Isolation | Non-isolated | Galvanically isolated (5 kV rms) | Isolation affects safety, ground-loop immunity, and whether external isolators are required in the design. |
| Duplex Mode | Half-duplex | Half-duplex (CAN bus) | Duplex configuration must match the bus topology and cabling of the intended application. |
| Package | 8-lead SOIC (R-8) | 20-lead SOIC_W (RI-20) | Footprint and pin count differences prevent direct board-level replacement. |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +125 °C | The wider temperature range of the CAN part suits harsher environments, while the RS-485 part is limited to industrial-standard ranges. |
| Fail-Safe Receiver | Yes (open/short fail-safe) | Yes (bus fault protection) | Fail-safe behavior ensures a defined logic state during idle or fault conditions, but the mechanisms differ by protocol. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADM3050EBRIZ | ADM3076EARZ |
|---|---|---|
| Series | iCoupler® | - |
| Part Status | Active | Active |
| Type | Transceiver, Isolated | Transceiver |
| Protocol | CAN | RS422, RS485 |
| Number of Drivers/Receivers | 1/1 | 1/1 |
| Receiver Hysteresis | 150 mV | 100 mV |
| Data Rate | 12Mbps | 16Mbps |
| Voltage - Supply | 0.5V ~ 6V | 3V ~ 3.6V |
| Operating Temperature | -40°C ~ 125°C | -40°C ~ 85°C |
| Mounting Type | Surface Mount | Surface Mount |
| Duplex | - | Full |
The ADM3076EARZ is a ±15 kV ESD protected, 3.3 V, full-duplex RS-485/RS-422 transceiver in an 8-lead SOIC package. The ADM3050EBRIZ is a 5 kV rms isolated CAN FD transceiver with an integrated isolated DC-to-DC converter, housed in a 20-lead SOIC_W package. They serve different bus protocols (RS-485 vs. CAN FD) and are not functionally interchangeable.
No. The ADM3076EARZ uses an 8-lead SOIC (R-8) package, while the ADM3050EBRIZ uses a 20-lead SOIC_W (R-20) package. Pin counts, pin functions, and PCB land patterns differ, so neither part can be dropped into the other's footprint.
The ADM3076EARZ is specified for data rates up to 16 Mbps over RS-485/RS-422. The ADM3050EBRIZ supports CAN FD data rates up to 5 Mbps. The applicable rate depends on the bus protocol and network topology in the target design.
The ADM3076EARZ provides ±15 kV ESD protection on the RS-485 bus pins but does not include galvanic isolation. The ADM3050EBRIZ provides 5 kV rms isolation per UL 1577 and CSA, with an integrated isolated DC-to-DC converter for the isolated side. The two parts address different safety and grounding requirements.
The ADM3076EARZ operates from a single 3.3 V supply. The ADM3050EBRIZ operates from a 5 V supply on the logic side and generates an isolated supply for the CAN bus side through its integrated DC-to-DC converter. Power architecture and decoupling requirements therefore differ between the two parts.
No. The ADM3076EARZ is an RS-485/RS-422 transceiver and does not implement the CAN or CAN FD protocol, nor does it provide isolation. The ADM3050EBRIZ is a dedicated isolated CAN FD transceiver. Substitution would require a protocol change and is not supported by the datasheets.
The ADM3076EARZ is typically used in industrial RS-485/RS-422 networks, building automation, and motor control buses requiring full-duplex communication. The ADM3050EBRIZ is intended for isolated CAN FD networks in industrial, automotive, and medical systems where galvanic isolation and higher-layer protocol compliance are required.