Part A
AD8058ARM
ADI公司
- Lifecycle
- Active
- Stock
- 5381 件
- Package
- MSOP-8
- Series
- 線性放大器-儀器、運算放大器、緩衝放大器
Replacement verdict
Compatible functional replacement candidate
The AD8058ARM and AD8052ARM-REEL are both dual high-speed voltage-feedback operational amplifiers from Analog Devices in the same 8-lead MSOP package, sharing identical pinout and similar supply and bandwidth characteristics. The AD8058ARM is a viable functional replacement candidate for the AD8052ARM-REEL in most dual-op-amp signal-chain applications, provided the designer validates the slightly different gain-bandwidth, slew-rate, and supply-current figures against the target circuit requirements.
Package Type
High match
Channel Count
High match
Gain Bandwidth Product
Validation required
Supply Current
Validation required
Parts at a glance
Part B
AD8052ARM-REEL
ADI公司
- Lifecycle
- Active
- Stock
- 2858 件
- Package
- TSSOP-8
- Series
- 線性放大器-儀器、運算放大器、緩衝放大器
Key differences
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | AD8058ARM | AD8052ARM-REEL | Why it matters |
|---|---|---|---|
| Number of Amplifiers | 2 | 2 | Both are dual op-amps, so channel count is compatible for dual-channel signal chains. |
| -3 dB Bandwidth | 325 MHz | 110 MHz | Higher bandwidth affects achievable signal frequency and settling performance in the application. |
| Slew Rate | 1000 V/µs | 170 V/µs | Slew rate limits large-signal transient response and distortion at high frequencies. |
| Supply Voltage Range | 3 V to 12 V | 3 V to 12 V | Compatible supply range allows operation from the same rails in a given design. |
| Input Offset Voltage (max) | 5 mV | 5 mV | Offset voltage impacts DC accuracy in precision signal conditioning paths. |
| Quiescent Current per Amplifier | 5.5 mA | 5.5 mA | Quiescent current determines power budget and thermal load in the system. |
| Package | 8-Lead MSOP | 8-Lead MSOP | Identical package enables drop-in board replacement without layout changes. |
| Output Current | 50 mA | 50 mA | Output drive capability affects ability to drive low-impedance loads or cables. |
Need help validating a replacement?
Send your BOM and application constraints for technical and sourcing review.
Full specification comparison
Use manufacturer datasheets as the final authority.
| Specification | AD8058ARM | AD8052ARM-REEL |
|---|---|---|
| Supplier | - | Analog Devices Inc.,Rochester Electronics, LLC |
| Part Status | Obsolete | Obsolete |
| Amplifier Type | Voltage Feedback | Voltage Feedback |
| Number of Circuits | 2 | 2 |
| Output Type | - | Rail-to-Rail |
| Slew Rate | 1150V/µs | 170V/µs |
| Gain Bandwidth Product | 100 MHz | 80 MHz |
| -3 dB Bandwidth | 325 MHz | 110 MHz |
| Current - Input Bias | 500 nA | 1.4 µA |
| Voltage - Input Offset | 1 mV | 1.7 mV |
| Supply Current | 14mA | 4.8mA (x2 Channels) |
| Current - Output / Channel | - | 45 mA |
| Voltage - Supply Span(Min) | 3 V | 3 V |
| Voltage - Supply Span(Max) | 12 V | 12 V |
| Operating Temperature | -40°C ~ 85°C | -40°C ~ 125°C |
| Mounting Type | Surface Mount | Surface Mount |
Frequently asked questions
What are the key differences between the AD8058ARM and AD8052ARM-REEL?
The AD8058ARM is a dual, low-power, high-speed voltage feedback operational amplifier, while the AD8052ARM-REEL is a dual, high-speed, low-power rail-to-rail output voltage feedback operational amplifier. The AD8052ARM-REEL is supplied in tape-and-reel packaging for automated assembly, whereas the AD8058ARM is typically supplied in tube or tray packaging. Both are dual op amps in 8-lead MSOP packages, but they differ in output swing characteristics and specified dynamic performance.
Are the AD8058ARM and AD8052ARM-REEL pin-compatible?
Yes. Both devices are offered in an 8-lead MSOP (RM) package with the same pinout: pin 1 = OUT1, pin 2 = -IN1, pin 3 = +IN1, pin 4 = V-, pin 5 = +IN2, pin 6 = -IN2, pin 7 = OUT2, and pin 8 = V+. This common pinout allows the devices to share the same PCB land pattern, but electrical differences must still be validated before substitution.
What is the difference in output swing between the AD8058ARM and AD8052ARM-REEL?
The AD8052ARM-REEL features a rail-to-rail output stage, allowing the output to swing close to both supply rails, which is advantageous in low-voltage or single-supply applications. The AD8058ARM has a standard output stage with more limited output swing relative to the supply rails. Designers should consult the respective datasheets for exact output voltage swing specifications under their intended load and supply conditions.
Can the AD8058ARM be replaced by the AD8052ARM-REEL in an existing design?
Because both are dual high-speed voltage feedback op amps in the same 8-lead MSOP package with identical pinouts, a replacement may be possible, but it is not a drop-in substitution without verification. Key parameters such as supply voltage range, quiescent current, bandwidth, slew rate, output swing, and capacitive load stability differ between the two devices. The replacement should only be made after confirming that the AD8052ARM-REEL meets all requirements of the target circuit per the manufacturer datasheet.
What supply voltage ranges do the AD8058ARM and AD8052ARM-REEL support?
Both devices are designed for operation on dual or single supplies. The AD8058ARM operates on a supply range of ±2.5 V to ±5 V (or 5 V to 10 V single supply), while the AD8052ARM-REEL operates on a supply range of 3 V to 12 V (or ±1.5 V to ±6 V). Exact minimum and maximum supply voltages should be confirmed against the latest manufacturer datasheets before use.
Why is the AD8052ARM-REEL supplied in tape-and-reel packaging?
The "-REEL" suffix indicates tape-and-reel packaging, which is intended for high-volume automated pick-and-place assembly lines. Tape-and-reel format improves manufacturing throughput and consistency compared to tube or tray packaging. The AD8058ARM is typically supplied in tube or tray format, so packaging format is a practical difference to consider when planning production.
Do the AD8058ARM and AD8052ARM-REEL have the same bandwidth and slew rate?
No. The two devices have different specified dynamic performance. The AD8058ARM is characterized with a -3 dB bandwidth of approximately 325 MHz and a slew rate of approximately 1000 V/µs, while the AD8052ARM-REEL is characterized with a -3 dB bandwidth of approximately 110 MHz and a slew rate of approximately 145 V/µs. These values are typical and should be verified against the manufacturer datasheets for the specific test conditions.
Which device is better suited for low-power portable applications?
Both devices are low-power dual op amps, but the AD8052ARM-REEL is often preferred for low-voltage, single-supply portable designs because of its rail-to-rail output stage and 3 V minimum supply operation. The AD8058ARM offers higher bandwidth and slew rate but requires a higher minimum supply and has more limited output swing. The final choice depends on the specific power, bandwidth, and output swing requirements of the application.